Suggestions
Products
See all results for products

DULCOTEST sensors for conductivity

Graduated measuring ranges 0.01 µS/cm – 2,000 mS/cm

Conductivity sensors for optimum process integration: DULCOTEST sensors meet a wide range of measuring requirements and allow the best solution to any given measuring task to be achieved.

Product description

Online measurement of electrolytic conductivity – with reliable DULCOTEST sensors.

Conductive conductivity sensors measure the electrolytic conductivity indirectly via the charge transfer between two probes immersed in the medium to be measured. The sensor types with cell constants k = 0.01 and k = 0.1 cm-1 are especially suitable for measuring the lowest electrolytic conductivities of < 1 µS/cm in pure and ultra-pure water.

The sensor types with cell constants k=1 cm-1 are used in numerous kinds of water without film-forming components up to 20 mS/cm. The cost-effective sensor range LF(T) is used in clear, chemically uncontaminated water.

The sensor ranges LM(P), CK and CKPt can also be used in chemically contaminated kinds of water and at higher temperatures.

Your benefits

  • 27 different sensor types tailored to different requirements and offering optimum performance for money: measuring range, temperature, chemical resistance, contamination tolerance and process integration
  • From simple conductometric sensors to high-end sensors based on the inductive measurement principle
  • Precise and reliable measurement enables efficient processes and maximum process reliability
  • Long service lives and short maintenance intervals reduce downtime and increase the availability of the measured values
  • Complete pre-assembled kits containing fitting and sensor for easy, fast and error-free installation
  • Prompt delivery for quick replacement

Field of application

The following list is a general representation of basically suitable applications for this product. Please contact your personal representative to discuss the use of the product in your individual application.

  • Metering and dilution of chemicals
  • Measuring the concentration of aggressive chemicals
  • Washing and cleaning processes, especially CIP (cleaning in place) processes in the food and beverage industry
  • Blowdown control in cooling towers
  • Control of ultra-clean, clean and potable water generation processes
  • Waste water

    Metering Chemicals in Coolant Treatment

    The secret of a highly durable coolant system

    We treat coolants with small quantities of chemicals, reducing the environmental footprint while protecting the system against corrosion, deposits and biological growth.
    more

    Monitoring and Replenishing of Electroplating Baths

    Demanding baths require concentration

    Baths have to be monitored and replenished continually. This requires high concentration - from the sensors, controllers and pumps. Yet only small amounts of precisely fed chemicals are needed.
    more

    Waste Water Treatment in the Paper and Pulp Industry

    Clean waste water is returned to nature

    Very low-impact treatment for waste water. Our intelligent processes efficiently clean and save money too.
    more

    Cooling Water Treatment in Energy Generation

    No biofilm, no bacteria, no dangerous by-products

    ProMinent metering pumps allow you to keep your cool at all times as you no longer need to concern yourself with the cooling process. Alternative biocides reliably prevent deposits.
    more

    Waste Water Treatment in Energy Generation

    Treating waste water quickly and thoroughly

    The benefits of our waste water treatment for energy generators can be easily summed up: our waste water treatment is thorough, environmentally-sound, economical and fully automatic. Because ProMinent thinks things through.
    more

    Desalination of Seawater and Brackish Water

    Obtaining additional potable water with desalination

    Drinkable water is scarce. Only a fraction of all the world's water can be consumed. So the ability to treat brackish water and seawater is of interest to many countries and islands.
    more

    Cleaning fruit and vegetables

    Simple and reliable cleaning process for agricultural products

    Fresh fruit and veg are an essential part of our diet. So it's very important for them to reach the consumer in a safe condition. Precise metering of chlorine dioxide ensures that this is the case.
    more

    Fish processing, fish and shrimp farming

    Successful farming and hygienic processing

    More and more people are enjoying delicacies from our seas. Fish farms and also the fish processing industry therefore face the huge challenge of producing goods quickly and hygienically. Disinfected water is essential to both industries.
    more

    CIP - Cleaning In Place

    CIP gets to work exactly where it's needed

    Small volumes of disinfectant are produced and used on site for sterile machines and process water. Highly concentrated, dangerous chemicals and tedious disassembly are a thing of the past.
    more

    Production of whey and cheese

    Perfect water for the entire production process

    To guarantee an end product fit for purpose, ProMinent ensures optimum water quality at every stage of production, thereby reliably complying with statutory hygiene standards.
    more

    Potable Water Treatment

    Outstanding water quality in line with global WHO standards

    ProMinent turns water into hygienically perfect potable water – with powerful systems and components, which can be ready mounted for operation or individually configured.
    more

    Conductivity Sensor LMP 001

    Sensor for measurement of the lowest electrolytic conductivities for clear and also chemically contaminated water. With integrated temperature measurement and DIN 4-pin plug. For operation with the controllers DCCa, DACb, DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.01 µS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.01…50 µS/cm

    Cell constant

    0.01 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 158 °F (0 … 70 °C)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Stainless steel 1.4571

    Sensor shaft

    PP

    Thread

    3/4”

    Installation length

    2.8 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Clean water applications, monitoring ion exchangers and reverse osmosis systems.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Controllers

    Compact DCCa, DACb, DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 001

    1020508

    Conductivity Sensor LMP 001-HT

    Sensor for measurement of the lowest electrolytic conductivity for clear and also chemically contaminated water. For high temperatures, with integrated temperature measurement and DIN 4-pin plug. For operation with the controllers DCCa, DACb, DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.01 µS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • Temperature resistance up to 212 °F (100 °C)

    Measuring range

    0.01…50 µS/cm

    Cell constant

    0.01 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 248 °F (0 … 120 °C)

    Max. pressure

    232 psi (212 °F / 100 °C)

    Sensors

    Stainless steel 1.4571

    Sensor shaft

    PVDF

    Thread

    3/4”

    Installation length

    2.8 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    General applications at higher temperatures, clean water applications, condensate.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Controllers

    Compact DCCa, DACb, DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 001-HT

    1020509

    Conductivity Sensor LMP 01

    Sensor for measurement of low electrolytic conductivities for clear and also chemically contaminated water. With integrated temperature measurement and DIN 4-pin plug. For operation with the controllers DCCa, DACb, DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 µS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.1…500 µS/cm

    Cell constant

    0.10 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 158 °F (0 … 70 °C)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Stainless steel 1.4571

    Sensor shaft

    PP

    Thread

    3/4”

    Installation length

    1.81 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Monitoring ion exchangers, reverse osmosis systems and desalination systems.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Controllers

    Compact DCCa, DACb, DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 01

    1020510

    Conductivity Sensor LMP 01-TA

    Sensor for measurement of low electrolytic conductivities for clear and also chemically contaminated water. With integrated temperature measurement and DIN 4-pin plug. For operation with the controllers DCCa, DACb, DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 µS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Simple installation in tanks and containers by sensor ready mounted in the immersion tube
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.1…500 µS/cm

    Cell constant

    0.10 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 158 °F (0 … 70 °C)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Stainless steel 1.4571

    Sensor shaft

    PP

    Thread

    M 28 x 1.5 for TA-LM in-line probe fitting

    Installation length

    Max. 3 ft

    Process integration

    Immersion through an immersion tube

    Electrical Connection

    16.4 ft fixed cable

    Enclosure rating

    IP 65

    Typical applications

    Monitoring ion exchangers, reverse osmosis systems and desalination systems.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Controllers

    Compact DCCa, DACb, DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 01-TA

    Sensor integrated in immersion fitting

    1020512

    LMP 01-FE

    Replacement sensor for LMP 01-TA with 16 ft fixed cable

    1020626

    Conductivity Sensor LMP 01-HT

    Sensor for measurement of low electrolytic conductivities for clear and also chemically contaminated water. For high temperatures, with integrated temperature measurement and DIN 4-pin plug. For operation with the controllers DCCa, DACb, DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 µm/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Temperature resistance up to 212 °F (100 °C)
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.1…500 µS/cm

    Cell constant

    0.10 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 248 °F (0 … 120 °C)

    Max. pressure

    232 psi (212 °F / 100 °C)

    Sensors

    Stainless steel 1.4571

    Sensor shaft

    PVDF

    Thread

    3/4”

    Installation length

    1.81 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    General applications at higher temperatures: industrial, process water, condensate.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Controllers

    Compact DCCa, DACb, DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 01-HT

    1020511

    Conductivity Sensor LFT 1 FE

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and fixed cable connector. For operation with controllers DMTa, D1Ca

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear uncontaminated water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • Fixed cable on the sensor head for difficult ambient conditions

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    16.4 ft fixed cable (4 x 0.5 mm2)

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DMTa, D1Ca

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFT 1FE

    1001374

    Conductivity Sensor LFTK 1 FE-5m-shd

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and fixed cable connector (16 ft / 5 m). For operation with controllers DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear uncontaminated water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 1000 for precise temperature compensation in limited temperature ranges replaces separate temperature sensor and the corresponding sensor fitting
    • Fixed cable on the sensor head for difficult ambient conditions

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 1000

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    16.4 ft fixed cable (4 x 0.25 mm2), screened

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFTK 1 FE-5m-shd

    1046132

    Conductivity Sensor LFTK 1 FE-3m-shd

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and fixed cable connector (10 ft / 3 m). For operation with controllers DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear uncontaminated water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 1000 for precise temperature compensation in limited temperature ranges replaces separate temperature sensor and the corresponding sensor fitting
    • Fixed cable on the sensor head for difficult ambient conditions

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 1000

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    9.8 ft fixed cable (4 x 0.25 mm2), screened

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFTK 1 FE-3m-shd

    1046010

    Conductivity Sensor LF 1 DE

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. For applications with a constant temperature, with DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear uncontaminated water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Cost-effective version without integral temperature measurement with constant temperature of the medium to be measured
    • DIN 4-pin plug for simple installation

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    None, only for applications with constant temperature

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes

    Order no.

    LF 1 DE

    1001375

    Conductivity Sensor LFT 1 DE

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear, uncontaminated types of water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • DIN 4-pin plug for simple installation

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable water, cooling water, industrial process water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFT 1 DE

    1001376

    Conductivity Sensor LFTK 1 DE

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water with integrated temperature measurement and DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear uncontaminated water
    • Flexible process connection by the use of sensor fittings for standard pH sensors
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • DIN 4-pin plug for simple installation

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 1000

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    PG 13.5

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFTK 1 DE

    1002822

    Conductivity sensor LFT 1 1/2"

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and DIN 4-pin plug and 1/2-inch screw-in thread. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Cost-effective sensor for all clear, uncontaminated types of water
    • Hydraulic connector with 1/2" thread as an alternative to the corresponding standard design with PG 13.5 thread
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • DIN 4-pin plug for simple installation

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    1/2”

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFT 1 1/2”

    1001378

    Conductivity sensor LFTK 1 1/2"

    Cost-effective sensor for measurement of electrolytic conductivity in clear, uncontaminated water. With integrated temperature measurement and DIN 4-pin plug and 1/2-inch screw-in thread. For operation with controllers DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µC/cm
    • Cost-effective sensor for all clear, uncontaminated types of water
    • Hydraulic connector with 1/2" thread as an alternative to the corresponding standard design with PG 13.5 thread
    • Special graphite electrodes, optimised for a highly dynamic measuring range: 0.01-20 mS/cm
    • Integrated Pt 1000 for precise compensation in limited temperature ranges and with longer cables. Replaces separate temperature sensor and the corresponding sensor fitting
    • DIN 4-pin plug for simple installation

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 1000

    Medium temperature

    32 … 176 °F (0 … 80 °C) (at 15 psi)

    Max. pressure

    232 psi (77 °F / 25 °C)

    Sensors

    Special graphite

    Sensor shaft

    Epoxy

    Thread

    1/2”

    Installation length

    4.72 ±0.12 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial water. Sensors of the LF series have only limited applicability for taking measurements in cleaning solutions containing surfactants and media containing solvents.

    Resistance to

    Unsuitable for chemically contaminated water and water containing film-forming ingredients

    Compatible controllers

    DCCa, DACb, DMTa, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LFTK 1 1/2”

    1002823

    Conductivity Sensor CK 1

    Sensor for measurement of electrolytic conductivity for clear, chemically contaminated water with higher but constant temperature with DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Resistant to water ingredients in target applications thanks to injection-moulded design without adhesive or seals
    • High temperature resistance up to 302 °F (150 °C)

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    None, only for applications with constant temperature

    Medium temperature

    32 … 302 °F (0 … 150 °C) (at 15 psi)

    Max. pressure

    232 psi (68 °F / 20 °C)

    Sensors

    Special graphite

    Sensor shaft

    PES

    Thread

    R 1”

    Installation length

    3.11 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Cooling, industrial, process water, tank and pipe, cleaning systems in breweries, dairies, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes

    Order no.

    CK 1

    305605

    Conductivity Sensor CKPt 1

    Sensor for measurement of electrolytic conductivity for clear, chemically contaminated water and higher temperatures. With integrated temperature measurement and DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 10 µS/cm
    • Resistant to water ingredients in target applications thanks to injection-moulded design without adhesive or seals
    • High temperature resistance up to 302 °F (150 °C)
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.01…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 302 °F (0 … 150 °C) (at 15 psi)

    Max. pressure

    232 psi (68 °F / 20 °C)

    Sensors

    Special graphite

    Sensor shaft

    PES

    Thread

    R 1”

    Installation length

    3.11 inch

    Process integration

    Bypass: with or without return of the sample water into the process line, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting), tank, channel: Immersion in the immersion tube

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Cooling, industrial, process water, tank and pipe, cleaning systems in breweries, dairies, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    CKPt 1

    305606

    Conductivity Sensor LM 1

    Sensor for measurement of electrolytic conductivity for clear and also chemically contaminated water. With DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 mS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Resistant to the constituents in the water of the target application

    Measuring range

    0.1…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    None, only for applications with constant temperature

    Medium temperature

    32 … 158 °F (0 … 70 °C) (at 15 psi)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Graphite

    Sensor shaft

    PP

    Thread

    3/4”

    Installation length

    1.81 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial, process water, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes

    Order no.

    LM 1

    740433

    Conductivity Sensor LM 1-TA

    Sensor for measurement of electrolytic conductivity for clear and also chemically contaminated water. Fully assembled in an immersion fitting. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 mS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Resistant to the ingredients in the water of the target applications
    • Simple installation in tanks, containers etc. by sensor ready mounted in the immersion tube

    Measuring range

    0.1…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    None, only for applications with constant temperature

    Medium temperature

    32 … 158 °F (0 … 70 °C) (at 15 psi)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Graphite

    Sensor shaft

    PP

    Thread

    M 28 x 1.5 for TA-LM in-line probe fitting

    Installation length

    Max. 3 ft

    Process integration

    Tank, channel: Immersion through an immersion tube

    Electrical Connection

    16.4 ft fixed cable, screened

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial, process water, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes

    Order no.

    LM 1-TA

    Sensor integrated in immersion fitting

    1020528

    LM 1-FE

    Replacement sensor for LM 1-TA

    1020627

    Conductivity Sensor LMP 1

    Sensor for measurement of electrolytic conductivity for clear and also chemically contaminated water. With integrated temperature measurement with DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 mS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Resistant to the ingredients in the water of the target applications
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting

    Measuring range

    0.1…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 158 °F (0 … 70 °C) (at 15 psi)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Graphite

    Sensor shaft

    PP

    Thread

    3/4”

    Installation length

    1.81 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial, process water, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 1

    1020513

    Conductivity Sensor LMP 1-TA

    Sensor for measurement of electrolytic conductivity for clear and also chemically contaminated water. With integrated temperature measurement, fully assembled in an immersion fitting. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 mS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Resistant to the ingredients in the water of the target applications
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • Simple installation in tanks, containers etc. by sensor ready mounted in the immersion tube

    Measuring range

    0.1…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 158 °F (0 … 70 °C) (at 15 psi)

    Max. pressure

    232 psi (122 °F / 50 °C)

    Sensors

    Graphite

    Sensor shaft

    PP

    Thread

    M 28 x 1.5 for TA-LM in-line probe fitting

    Installation length

    3 ft

    Process integration

    Tank, channel: Immersion through an immersion tube

    Electrical Connection

    16.4 ft fixed cable, screened

    Enclosure rating

    IP 65

    Typical applications

    Potable, cooling, industrial, process water, media separation.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes

    Order no.

    LMP 1-TA

    Sensor integrated in immersion fitting

    1020525

    LMP 1-FE

    Replacement sensor for LMP 1-TA

    1020727

    Conductivity Sensor LMP 1-HT

    Sensor for measurement of electrolytic conductivity for clear and also chemically contaminated water. For high temperatures, with integrated temperature measurement and DIN 4-pin plug. For operation with controllers DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Your Benefits

    • Measured variable: electrolytic conductivity above 0.1 mS/cm
    • Cost-effective sensor for clear, chemically contaminated water
    • Resistant to the ingredients in the water of the target applications
    • Integrated Pt 100 for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • Temperature resistance up to 212 °F (100 °C)

    Measuring range

    0.1…20 mS/cm

    Cell constant

    1.00 cm-1 ±5 %

    Temperature measurement

    Pt 100

    Medium temperature

    32 … 248 °F (0 … 120 °C) (at 15 psi)

    Max. pressure

    232 psi (212 °F / 100 °C)

    Sensors

    Graphite

    Sensor shaft

    PVDF

    Thread

    3/4”

    Installation length

    1.81 inch

    Process integration

    Inline: direct installation into the pipework, bypass: with or without return of the sample water into the process line

    Electrical Connection

    DIN 4-pin angle plug

    Enclosure rating

    IP 65

    Typical applications

    General applications at higher temperaturesprocess water, process water from electroplating, media separation, with CIP (cleaning in place).

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DCCa, DACb, DMTa, D1Ca, AEGIS II, AEGIS X

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement

    Order no.

    LMP 1-HT

    1020524

    Conductivity sensor CCT 1-mA

    Sensor for measurement of electrolytic conductivities for clear and also chemically contaminated water. With integrated temperature measurement and factory-calibrated 4...20 mA output signal. For operation with controllers DAC, D1C, AEGIS II, AEGIS X, DULCOMARIN.

    Your Benefits

    • Measured variable: electrolytic conductivity up to 20 mS/cm
    • Fail-safe 4-20 mA output signal for flexible connection to measuring equipment with standard 4-20 mA input
    • Integrated temperature sensor for temperature compensation replaces separate temperature sensor and the corresponding sensor fitting
    • Simple connection to a process with the ProMinent bypass fittings BAMa, DGMA, DLGIII and INLI

    Measuring range

    0.2…20 mS/cm

    Temperature measurement

    NTC, integrated

    Medium temperature

    32 … 122 °F (0 … 50 °C) (at 15 psi)

    Max. pressure

    116 psi (77 °F / 25 °C)

    Sensor head

    PMMA

    Sensors

    Special graphite

    Sensor shaft

    PVC

    Installation length

    2 inch / 2.8 inch

    Process integration

    Bypass via bypass fittings BAMa, DGMa, DLGIII or installation into G1” PP pipe via sensor fitting INLI

    Electrical Connection

    4-wire cable, 0.25 mm², cable diameter 5.7

    Supply voltage

    12…36 V DC

    Output signal

    4…20 mA, temperature-compensated, factory-calibrated, electrically isolated

    Enclosure rating

    IP 65

    Typical applications

    Cooling, industrial, process water, general water with higher salt content up to 20 mS/cm.

    Resistance to

    Ingredients in the water of the target application, taking into account the compatibility of the material

    Compatible controllers

    DAC, D1C, AEGIS II, AEGIS X, DULCOMARIN

    Measuring principle, technology

    Conductive, 2 electrodes. Integrated temperature measurement, integrated 4...20 mA transducer

    Order no.

    CCT 1-mA-20 mS/cm

    1081545

    Conductivity sensor ICT 5

    Cost-effective inductive conductivity sensor, suitable for high electrolytic conductivities above 200 µS/cm. Also suitable for chemically contaminated water and film-forming media. For installation in pipework

    Your Benefits

    • Measured variable: electrolytic conductivity. The inductive (non-contact) measuring principle permits applications in chemically contaminated types of water and in film-forming media
    • Complete with injection moulded PP sensor head, no apparent bonds, seals
    • Measurements at high conductivity values of up to 2,000 mS/cm are possible without interfering polarisation by means of the high measuring range dynamics of the inductive measuring principle
    • Simple installation in PVC pipework by bonding the DN 40 adhesive connector supplied into a standard T-piece and screwing in the sensor using the union nut supplied.
    • A DN 40 welded connector is optionally available for use in PP pipework

    Measuring range

    0.2…2,000 mS/cm

    Cell constant

    6.25 cm-1

    Measuring accuracy

    ±2% based on the measured value ±30 μS/cm

    Temperature sensor

    Pt 1000, wetted material Stainless steel 1.4301

    Medium temperature

    14...176 °F (-10...80 °C) 14...140 °F (-10...60 °C) for installation in PVC pipes, 14...176 °F (-10...80 °C) for installation in PP pipes

    Max. pressure

    145 psi at 68 °F (20 °C), 87 psi at 140 °F (60 °C), 0.0 psi at 176 °F (80 °C)

    Min. pressure

    -1.5 psi (14 … 176 °F / -10 … 80 °C)

    Sensor material

    PP

    Seals

    EPDM

    Electrical Connection

    32.8 ft fixed cable, 7x 0.35 mm² via a terminal

    Enclosure rating

    IP 65

    Typical applications

    Contaminated waste water, blowdown control in cooling towers, control of electroplating and rinsing baths, cleaning in Place (CIP), product monitoring, sea water, brine swimming pools.

    Resistance to

    Ingredients in the water of the target application, taking into account compatibility to PP/EPDM, deposit-forming media

    Process integration

    With union nut, PVC, 1 1/2 inch female thread, including DN 40 bonded nozzle with 1 1/2 inch male thread for fitting in DN 40 PVC standard pipes (included in the scope of delivery). The corresponding set-in nozzle for fitting in PP standard pipes is available as an accessory

    Controllers

    Compact controller DCCa

    Measuring principle, technology

    Inductive, 2 coils. Integrated temperature measurement

    Order no.

    ICT 5

    1095248

    Conductivity Sensor ICT 5-IMA

    Cost-effective inductive conductivity sensor, suitable for high electrolytic conductivities above 200 µS/cm. Also suitable for chemically contaminated water and film-forming media. Completely integrated in an immersion pipe

    Your Benefits

    • Measured variable: electrolytic conductivity. The inductive (non-contact) measuring principle permits applications in chemically contaminated types of water and in film-forming media
    • Complete with injection moulded PP sensor head, no apparent bonds, seals
    • Measurements at high conductivity values of up to 2,000 mS/cm are possible without interfering polarisation by means of the high measuring range dynamics of the inductive measuring principle
    • Simple installation in tanks, containers etc. thanks to sensor ready mounted in the immersion tube

    Measuring range

    0.2…2,000 mS/cm

    Cell constant

    6.25 cm-1

    Measuring accuracy

    ±2% based on the measured value ±30 μS/cm

    Temperature sensor

    Pt 1000, wetted material Stainless steel 1.4301

    Medium temperature

    14...140 °F (-10...60 °C)

    Max. pressure

    0 psi

    Min. pressure

    -1.5 psi (14 … 140 °F / -10 … 60 °C)

    Sensor material

    PP

    Immersion pipe material

    PP

    Sensor guard material

    SS 1.4301, AISI 304

    Seals

    EPDM

    Electrical Connection

    32.8 ft fixed cable, 7x 0.35 mm² via a terminal

    Enclosure rating

    IP 65

    Typical applications

    Contaminated waste water, blowdown control in cooling towers, control of electroplating and rinsing baths, cleaning in Place (CIP), product monitoring, sea water, brine swimming pools.

    Resistance to

    Ingredients in the water of the target application, taking into account compatibility to PP/EPDM, deposit-forming media

    Process integration

    Immersion with immersion length 1 m

    Controllers

    Compact controller DCCa

    Measuring principle, technology

    Inductive, 2 coils. Integrated temperature measurement

    Order no.

    ICT 5-IMA

    1095249

    Conductivity Sensor ICT 2

    High-performance inductive conductivity sensor with high dynamic measuring range. Also suitable for types of water with aggressive chemicals and film-forming components. Permitted temperatures up to 257 °F (125 °C). For installation in pipework, tanks and for immersion in storage tanks

    Your Benefits

    • Measured variable: electrolytic conductivity. The inductive (non-contact) measuring principle permits applications in chemically contaminated types of water and in film-forming media
    • There is no need for adhesive or seals as the sensor is fully embedded in PFA
    • Measurements at high conductivity values of up to 2,000 mS/cm are possible without interfering polarisation by means of the high measuring range dynamics of the inductive measuring principle
    • Flexible connection to the processes is possible via a flange or immersion pipe with optional accessories

    Measuring range

    0.02…2,000 mS/cm

    Cell constant

    1.98 cm-1

    Measuring accuracy

    ±(5 μS/cm + 0.5 % of measured value) at T < 212 °F (100 °C)
    ±(10 μS/cm + 0.5 % of measured value) at T > 212 °F (100 °C)

    Temperature compensation

    Pt 100, class A, completely extrusion-coated

    Medium temperature

    32…257 °F (0…125 °C), when used together with D1C, temperature compensation is limited to 212 °F (100 °C)

    Max. pressure

    232 psi

    Sensor material

    PFA, completely extrusion-coated

    Electrical Connection

    16.4 ft fixed cable, 6x 0.35 mm² via a terminal

    Enclosure rating

    IP 67

    Typical applications

    Production processes in the chemical industry, phase separation of product mixtures, determination of concentrations of aggressive chemicals.

    Resistance to

    Electrolytic conductivity of > 20 mS/cm, PFA-compatible aggressive chemicals (no concentrated lyes), deposit-forming media

    Process integration

    Fitting in pipes, tanks (sideways): G 3/4 stainless steel thread (1.4571) or flange fitting: With the accessories: Stainless steel flange ANSI 2 inch 300 lbs, SS 316L (adaptable to DIN counter flange DN 50 PN 16).

    Controllers

    Compact controller DCCa

    Measuring principle, technology

    Inductive, 2 coils. Integrated temperature measurement

    Order no.

    ICT 2

    1023352

    Conductivity sensor ICT 8-mA

    Inductive sensor for the measurement of electrolytic conductivity. Suitable for contaminated water. With integrated temperature correction and factory-calibrated 4...20 mA output signal.

    Your Benefits

    • Measured variable: electrolytic conductivity up to 200 mS/cm without polarisation effect
    • The inductive (non-contact) measuring principle permits applications in water with solids content and in film-forming media
    • Fail-safe 4-20 mA output signal for flexible connection to measuring equipment with standard 4...20 mA input
    • Integrated temperature correction replaces separate temperature sensor and sensor fitting

    Measuring range

    three configurable measuring ranges 0.2...2.0 mS/cm / 0.5...20 mS/cm / 1...200 mS/cm

    Temperature correction

    integrated in the sensor electronics, temperature co-efficient: 1.7%/K

    Medium temperature

    max. 122 °F (50 °C) at 14 psi

    Sensor material

    PP

    Seals

    EPDM

    Installation length

    2.95 inch

    Electrical Connection

    Fixed cable, 6-wire (6x0.25 mm2). The cable length is 6.5 ft between the sensor and 4-20 mA cable transmitter and 32 ft between the cable transmitter and monitor.

    Typical applications

    Desalination control in cooling towers, contaminated waste water, control of electroplating and rinsing baths, salt water desalination, adjustment of the salt content in swimming pool water

    Resistance to

    Water ingredients in the target application, taking into account compatibility to PP/EPDM and combating film-forming media

    Process integration

    1/2” male thread (BSP) for mounting using flange,
    installation in PVC pipes, DN 50 by means of installation adapter ICT8, DN 50, PVC, order no. 1106570,
    immersion using immersion pipe, 1 m, order no. 1105964

    Compatible controllers

    DAC, D1C, AEGIS II, AEGIS X, DULCOMARIN

    Measuring principle, technology

    Inductive, 2 coils. Integrated temperature measurement, integrated 4...20 mA transducer

    Order no.

    ICT 8 -mA-200 mS/cm

    1098530

    Downloads for DULCOTEST sensors for conductivity

    More in the Download Centre

    0 Results
    Filter by document type
    Application Example / Reference (0)
    Brochure / Flyer (0)
    Catalogue (0)
    Certificate / Declaration (0)
    Data Sheet (0)
    Drawing / Dimensional Drawing / 3D (0)
    Exploded View / Spare Parts (0)
    Material Safety Data Sheet (0)
    Operating Instructions (0)
    Others (0)
    Press Release (0)
    Publication / Article (0)
    Software (0)
    Wiring Diagram (0)
    Selected filters:

    Matching downloads

    Sort by A to Z
    Load more matches ...
    No more matches available!

    Unfortunately, we did not find an appropriate match.

    All words written correctly?
    Search again with fewer or different search terms?

    Please try again later

    Service Unavailable

    The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.

    Overview

    Online measurement of electrolytic conductivity – with reliable DULCOTEST sensors.

    Conductive conductivity sensors measure the electrolytic conductivity indirectly via the charge transfer between two probes immersed in the medium to be measured. The sensor types with cell constants k = 0.01 and k = 0.1 cm-1 are especially suitable for measuring the lowest electrolytic conductivities of < 1 µS/cm in pure and ultra-pure water.

    The sensor types with cell constants k=1 cm-1 are used in numerous kinds of water without film-forming components up to 20 mS/cm. The cost-effective sensor range LF(T) is used in clear, chemically uncontaminated water.

    The sensor ranges LM(P), CK and CKPt can also be used in chemically contaminated kinds of water and at higher temperatures.

    Your benefits

    • 27 different sensor types tailored to different requirements and offering optimum performance for money: measuring range, temperature, chemical resistance, contamination tolerance and process integration
    • From simple conductometric sensors to high-end sensors based on the inductive measurement principle
    • Precise and reliable measurement enables efficient processes and maximum process reliability
    • Long service lives and short maintenance intervals reduce downtime and increase the availability of the measured values
    • Complete pre-assembled kits containing fitting and sensor for easy, fast and error-free installation
    • Prompt delivery for quick replacement

    Application

    Technical Data

    Downloads

    Find local ProMinent representative

    Contact us

    ProMinent Fluid Controls, Inc.


    sales-us@prominent.com

    +1 412-787-2484   
    sales-us@prominent.com Send request    

    »We are looking forward to your enquiry.«

    +1 412-787-2484 

    Spare Parts and Accessories

    Bypass Fittings for Sensors

    In-flow measurement

    Your sensors are ideally accommodated in the bypass fitting. This fitting ensures optimum measuring conditions.

     more

    Consumables for Conductivity Sensors

    The best solution for sensors

    The right calibration solution or test and calibration kit ensure accurate results from your conductivity sensors.

     more

    Immersion Fittings for Sensors

    Getting stuck in

    Your sensor is ideally accommodated in the immersion fitting. This fitting ensures optimum measuring conditions.

     more

    Measuring Lines for Conductivity Sensors

    Integrating your conductivity sensor into the measuring point

    A conductivity sensor alone is not enough. The right accessories integrate it optimally into the process!

     more

    Two-Wire Measuring Lines for Sensors

    Integrating your sensor into the measuring point

    A sensor alone is not enough. The right accessories integrate it optimally into the process!

     more

    Matching Products

    beta b Solenoid Diaphragm Metering Pump

    0.20 to 8.45 gph (0.74 to 32 l/h) at pressures up to 363 psi

    The ProMinent beta is a microprocessor-based diaphragm solenoid metering pump capable of flows from 0.16 to 8.45 gph (0.59 to 32 l/h) and pressures to 363 psi (25 bar).

    more

    Measuring and control device DULCOMETER Compact

    The measuring and control device DULCOMETER Compact for pH and redox measured variables is equipped with the standard functions for use in water treatment plants, allowing the operator to switch between the measured variables pH and redox, and between P and PID control characteristics.

    more

    gamma/ X Solenoid Diaphragm Metering Pump

    0.61 to 11.89 gph (2.3 to 45 l/h) at pressures up to 363 psi

    The solenoid-driven diaphragm metering pump gamma incorporates a wealth of eXcellent ingenuity! With integrated pressure measurement, it ensures the smooth running of your metering process. The gamma/ X is ideal for all metering work involving liquid media.

    more

    gamma/ XL Solenoid Diaphragm Metering Pump

    0.08 gpd to 20.74 gph (12.6 ml/h to 78.5 l/h) at pressures up to 363 psi

    The gamma/ XL is a smart, connectible solenoid-driven metering pump that is setting new standards in terms of productivity, reliability and cost-effectiveness.

    more

    DULCOTEST pH sensors

    Graduated pH measuring ranges 0 – 14

    pH measurements with DULCOTEST sensors: Precise, reliable and application-adapted measured values in real time. Control, regulate and monitor chemical processes with the aid of precise measured values.

    more

    DULCOTEST sensors for peracetic acid

    Graduated measuring ranges 0.02 – 2,000 mg/l

    Measurement of peracetic acid concentration with DULCOTEST sensors: Precise and reliable for disinfection in safety-sensitive applications in the food, pharmaceutical and medical industries. Can also be used in waste water treatment.

    more

    Controller DULCOMETER diaLog DACb

    The DULCOMETER DACb controller uses intelligent controller functions to close the control circuit between ProMinent DULCOTEST sensors and ProMinent metering pumps.

    more

    Case studies for this product

    +1 412-787-2484
    Request
    Newsletter
    Request
    Newsletter